“Mineral-only” sunscreens are making huge inroads into the sunscreen market, driven by fears of “chemicals,” a belief that “mineral” products are inherently safer, and confusion about how sunscreens actually protect our skin.
How mineral sunscreens actually work is not widely understood, and neither is what’s actually in them. We tested ten of these sunscreens in the lab and reviewed the ingredient lists of over 100 more to clarify what’s going on.
We verified that many products marketed as “mineral-only” rely on a broad palette of chemicals, not only to make them nicer to use, but also to boost their sun protection factor (SPF) rating.
Mineral and chemical sunscreens
Most sunscreens contain just a handful of “active” ingredients: avobenzone, homosalate, octinoxate, octisalate, octocrylene, oxybenzone, or zinc oxide.
The active ingredients in sunscreens are generally divided into two main categories:
- inorganic ingredients, often described as “physical” or “mineral” — usually titanium dioxide or zinc oxide. These inorganic minerals are often reported to reflect UV rays. The reality is that these compounds mostly absorb UV light
- organic ingredients, often called “chemicals” — such as octinoxate, avobenzone, and homosalate. These are organic molecules that strongly absorb UV light and do not break down to form harmful substances.
Sunscreens are often marketed as either “chemical” or “mineral.” Mineral sunscreens are commonly said to “reflect” UV light, but our measurements reinforce what sunscreen experts and formulators know: that both mineral and organic filters work mainly by absorbing UV radiation.
‘Mineral’ sunscreens have chemicals, too
The goal of our study was simple: to understand how sunscreens achieve high SPF, and to understand the role of chemistry in sunscreens. We measured the absorption of different frequencies of UV light by pure zinc oxide, as well as 10 commercially available sunscreens.
We then identified 143 sunscreens listed on Australia’s Therapeutic Goods Administration register where zinc oxide or titanium dioxide were the only declared active ingredients. For each product, we also looked at the full list of ingredients — not just the “active” ones — scanning for any compounds known to absorb UV light.
Our measurements on zinc oxide showed strong UV absorption, as we expected from knowing its chemistry. This confirms that mineral sunscreens work via absorbing UV light, just like organic sunscreens.
When we looked at “mineral” sunscreens, we found some use additional UV-absorbing chemicals. We could see this because zinc oxide absorbs light fairly evenly across the UV spectrum, but organic chemicals tend to show “humps” in absorbance in particular frequency ranges.
Indeed, it is difficult to make a very high-SPF sunscreen that is pleasant to use using only mineral filters. The minerals would need to make up around 20 percent of the sunscreen by weight, but minerals are dense and can easily settle out of the mixture.
The formula would likely need to be thickened to stop the minerals from separating out. The mineral particles can also scatter visible light, leaving a “white cast,” which consumers also dislike.
A solution?
So how do you make a high SPF “mineral” sunscreen that’s lightweight and transparent?
One way is to use smaller mineral particles. These, however, increase the cost of the product and can pose other stability challenges.
Many brands use chemicals, such as butyloctyl salicylate and ethylhexyl methoxycrylene, to improve the sunscreen’s stability and keep the consistency smooth, but these molecules also strongly absorb UV light. However, these chemical UV filters do not have to be listed as “active ingredients” because their primary role is to serve another function.
In our test of 10 products, we found that two products claiming to be “mineral only” showed the telltale absorbance hump of organic chemical filters, due to the presence of butyloctyl salicylate and/or ethylhexyl methoxycrylene.
Indeed, we noticed something similar in our review of sunscreens on the Therapeutic Goods Register. At least 48 of 143 sunscreens listing only mineral active ingredients (~34 percent) contained additional chemicals known to strongly absorb UV light.
We also compared two “zinc-only” children’s sunscreens with very different skin-feels: one is thick, the other silky.
Our in-lab analysis (and the ingredient lists) showed that the silky product included UV-absorbing molecules. These may help make it easier to spread on skin, reduce white cast, and improve film formation.
We also confirmed that SPF increases after a sunscreen dries, with a successful formulation resulting in an even film. Without the right chemicals, the film would bead up, resulting in patchy protection.
The right chemistry
Sunscreen makers are quiet heroes helping us stay safe in the sun. They work really hard to make sunscreens feel good, be effective, and still be affordable.
People often turn to “clean” or “natural” products because they want something gentle. But gentle doesn’t mean avoiding “chemicals.” It comes from using the right chemistry.
Many carefully chosen ingredients are there simply to keep a formula stable, smooth, and safe on hot summer days.
A sunscreen that feels good, spreads evenly, and stays consistent is far safer than one that’s “natural,” but separates, goes off, or fails to form a reliable film on the skin.
Anna Wang, Associate Professor of Chemistry, UNSW Sydney; Jon Beves, Professor of Chemistry, UNSW Sydney, and Timothy Schmidt, Professor of Chemistry, UNSW Sydney
This article is republished from The Conversation under a Creative Commons license. Read the original article.
Follow us on X, Facebook, or Pinterest
